Finished Cutting

I am now finished cutting all the pieces, except the frame.  I need to get some more dark wood to do that.  The bottom part turned out to be as difficult as I thought.  There are lots of curves and I used some very hard wood.  The two pieces of White Oak were the worst.  Even with a new blade it was hard to cut on the lines.  The piece of Poplar I was using ended up being a little warped so it was very difficult to cut and now the edges aren't straight and so the pieces don't fit together all that well.  I have a lot of time ahead of me sanding and fitting to try and make the pieces fit better.  I will do that along with shaping and making the different levels so hopefully it all comes together at the same time.

Fitting this many pieces together is very hard and getting one piece to fit good throws off the next piece.  I can tell this will take a lot of practice.  I have a feeling that the joints between the land pieces won't be as noticeable as the joints between the lighthouse or the house pieces.  I think my next step will be to glue together the lighthouse and the houses so they fit together nicely then start working on the background around them.  At that point I will probably start from the top and work to the bottom, making sure every piece butts up against the pieces above it well so when I get to the bottom, I am hoping for a good result.

I have started trying to fit a few of the pieces together.  I have tried trimming them with the scroll saw and sanding the edges with a rotary tool.  The rotary tool works well but it is hard to keep a 90 degree edge.  I can tell now the benefits of a spindle sander.  That would do what the rotary tool does but it has a flat surface so you can keep perfectly straight edges.

First true intarsia project

I have decided to finally bite the bullet and try my hand at true intarsia.  I have a few books I have been studying and I have decided to try the Lighthouse project in "Intarsia Woodworking Projects" by Kathy Wise.  It is supposed to be an Intermediate level project but I want to do something interesting and the Beginner projects didn't interest me.  There is a little family history surrounding lighthouses and ocean coves so this will mean something to the family.

I have been collecting some wood over time and so after I went to Fedex Office and made several copies of the pattern I sat down to figure out what wood to use.  This is a rather large piece at about 14" X 18" and about 50 pieces.  After deciding what wood to use I cut out all the pattern pieces and applied them to the wood paying attention to grain direction and keeping continuous grain on continuation pieces like the sky from one side of the lighthouse to the other.  Here is my progress so far.

I have used Alder, Red Cedar, and Ash for the sky pieces.  The mountain background is Walnut.  The lighthouse is Walnut, Aspen, and Cherry.  The water is Blue Pine or some call it Beetle Kill Pine.

I have decided to use Aspen and Cherry for the houses and house tops.  The rocks will be Walnut.  The land will be Green Poplar and White Oak.  I found a piece of Poplar that is very green so it should work nicely.  The windows will be a small piece of Madagascar Ebony.  I found a 1" x 1" x 12" piece of Ebony at Woodcraft for $12.00.  Pricey but it should last me a long time.  I will shim up the Ebony pieces with something cheap so I don't have to use as much.

This is the first time I have cut anything besides Pine and Poplar.  There is sure a big difference between types of wood.  The Alder and the Ash were very hard and the cutting went slower.  The biggest difference I saw was how you have to feed the wood into the blade.  You always have to feed the wood in a little from the right to get a straight line but I found the harder the wood, the bigger angle you have to make to the blade.  The hardest part was going from one kind of wood to another and having to adjust how you feed the wood into the blade to get the same cuts.

The cedar and the walnut were pretty hard too.  The Blue Pine cut about like regular pine but the Aspen was very soft.  It cut fast so I had to be careful not to push too hard or the blade would take off.  Even the sawdust from the Aspen is very soft and fluffy.

As you can see the hardest cutting part is yet to come.  Getting all these pieces to fit together will be a challenge.  What I have done already has been hard so we will see how it goes.